Notre nouveau catalogue Soudage-Coupage 2024 est disponible Découvrir close
Accueil » Rechercher un produit
XHS-300 SERIES - DIAPHRAGM SENSED PRESSURE REGULATOR WITH SINGLE 100W HEATER

An economical heated regulator available in ‘side entry’ or ‘in-line’ heat transfer options to maintain sample gases in their vapour state. The ‘in-line’ design maximizes the heat transfer area via a unique spiral machined heater sheath, which mixes the gas and ensures efficient heat transfer. The ‘side entry’ design can be used in applications where heat transfer is less critical, and where install

LF-230 SERIES - LOW FLOW PRESSURE REGULATOR

FEATURES 316L SS Machined Wetted Parts Large sensitive elastomeric diaphragm 0,1 bar to 10 bar / 1,5 psi to 150 psi control range Minimal decaying inlet pressure effect For flow rates to 30Nm³/hr (@ max P2)

BP-301 SERIES - BACK PRESSURE REGULATOR

The BP-301 incorporates a highly sensitive piston to control pressures up to 70 bar with the lower Cv value of 0.1, and 35 bar with a higher Cv of 0.5. Both designs provide accurate back pressure control on liquid or gas applications. Unlike relief valves, the set load from the spring is not directly applied to the seating area, and the piston sensor provides accurate control throughout the control range. FEATURES Lightweight compact design

TS-300 SERIES - TWO STAGE PRESSURE REDUCING REGULATOR

The TS-300 provides stable pressure control under decaying cylinder pressures. The first stage of the regulator is set to 35 bar to allow maximum flow capability through the regulator. SPECIAL FEATURES Metal to metal sealing diaphragm Sealing area protected and centralized within the body of the regulator 0,04 % decaying pressure effect ‘Interstage’ relief valve option

BP-300 SERIES - LOW FLOW BACK PRESSURE REGULATOR

The BP-300 has been designed with a convoluted Inconel X750 diaphragm that lasts 50 % longer than a typical stainless steel designs. Its compact simple design makes it ideal for general purpose applications, where accurate control of upstream pressure is required. FEATURES Metal to metal diaphragm sealing Positive sealing against Viton seat Lightweight compact design Strong and sensitive diaphragm element High Accuracy

MEDIFLOW® II 50 lpm

Whole medical range is available on gcehealthcare.com Mediflow® II 50 lpm is a flow selector intended for use for resuscitation and for CPAP. Innovative self centering flow setting device with continuous flow between settings. In the unlikely event of indent mechanism failure, the patient will still be supplied by medicinal gas Lateral and frontal reading of flow setting Enables to get up to 50 lpm for supplying machines (not for use

GAS MANIFOLD SIMPLEX MMR

Whole medical range is available on gcehealthcare.com The Simplex MMR gas manifold is suitable for such health care where the capacity requirement is limited, such as laboratories and small health care clinics, veterinary etc. This gas manifold consists of only one group of cylinders. The regulator is mounted in the collection unit. Each inlet connection has a filter, a non-return valve and a shut-off valve. This arrangement makes it possilble

LF-300 SERIES - LOW FLOW PRESSURE REDUCING REGULATOR 35 BAR

The LF-300 has been designed with quality and reliability in mind, with genuinely unique features designed into this single stage regulator. Finite Element Analysis, combined with physical cycle tests, created an Inconel X750 diaphragm that lasts 50 % longer than a typical stainless steel designs.The metal diaphragm means that leak integrity is maintained, and that no sample media is absorbed by the sensing element – reducing purge times be

SMD 502/532-27. 2-STAGE, 6.0 INERT PURGING

Compact single-stage gas supply panel for corrosive or toxic gases and mixtures up to purity 6.0. Includes an upstream purge block for inert gas purging, upstream and downstream pressure gauges and a relief valve  For the connection of 1 cylinder with a maximum filling pressure of 230 bar (SMD500-26) and 300 bar (SMD530-26). Diaphragm type regulator and isolation valve. For wall mounting or gas cylinder cabinet mounting Excellent and acc

HOSE ISO3821 - SINGLE ARGON

Rubber hose for use with Argon in cutting and welding and allied processes. Suitable also for hydrogen, CO2, Nitrogen for welding and cutting. Not suitable for LPG, MPS and CNG. Inner tube: Synthetic rubber resistant to the welding gases Reinforcement: High tensile synthetic textile External cover: Black synthetic rubber resistant to abrasion and weather Smooth surface Temperature: -20°C / +60°C Safety factor: 3 : 1 Marking: In c